Recovery playbooks · Duplicate payments

Paying the full invoice after a deposit or prepayment

A deposit paid up front is not applied when the final invoice arrives, so the supplier is paid the deposit twice: once in advance and again inside the full invoice.

In short

  • Prepayments sit as debit balances on the vendor until they are applied.
  • The final invoice may or may not show the deposit as already received.
  • Every open prepayment should have a PO or contract reference to match it to the final invoice.
  • An aging report with vendor debit balances is the place to start.
  • The supplier's statement will show the deposit; if it shows the final invoice paid in full, the deposit is a credit.

How it happens

A deposit is paid before goods arrive and recorded as a prepayment, so it sits as a debit balance on the vendor record. The final invoice then arrives for the full order value. If the invoice does not show the deposit as received and the clerk keys it against the purchase order without checking the open balance, the payment run releases the full amount. The supplier has been paid the deposit twice.

The mismatch often starts at the document level. The deposit may have been requested on a pro forma invoice, while the final invoice references a different number, ship date or billing entity. The supplier's billing team may not link the two documents, so the final invoice states the balance due on the order as they see it, or says nothing about the deposit. The clerk sees a clean invoice, a valid purchase order and an approval, and pays it.

It also happens when the deposit was never set up as a prepayment. If the deposit invoice was coded to expense or to the wrong vendor record, there is no open debit balance to catch during matching. The same result occurs when a deposit is paid against one purchase order and the final invoice arrives under a second purchase order created later. Partial receipts make it worse: if receiving closes the original line at the deposit stage and a new line is opened for the balance, the two records never meet.

Finding it in your payment history

Start with an aging report that shows vendor debit balances, not just the credit balances that normally draw attention. An unapplied prepayment sits there as a debit. Pull every open prepayment and ask for the purchase order or contract reference behind it. A prepayment with no reference, or one pointing to an order that has since been closed and invoiced in full, is the first place to look.

Take the vendor statement next. The supplier's records will show the deposit as a receipt. If the statement also shows the final invoice paid in full, the deposit is sitting as a credit on their side. Compare the statement line by line against your payment history for that vendor, not just against the invoices on file.

Work backward from the final invoice. For any invoice covering the full value of an order, check the vendor record for an earlier payment on the same purchase order or contract. Search payment history by purchase order number, contract reference and amount, since a deposit is often a round figure paid weeks or months earlier. If a payment appears twice against the same order under different references, trace both to source documents.

Do not rely on the invoice to tell you whether the deposit was applied. Some suppliers show a deposit line; many do not. The reliable test is whether the vendor record still carries an open debit balance for that order after the final invoice is paid.

Getting the money back

Gather the deposit payment record, the purchase order or contract, the final invoice and the remittance advice, and send them to the supplier's accounts receivable contact with a short written request. Ask for a credit memo applied to the open balance or a refund, whichever the supplier prefers and the contract allows. Be specific: the date of the deposit payment, the amount, the reference it was paid under, and the final invoice it should have reduced.

If the supplier's statement already shows the deposit as an unapplied credit, ask them to apply it to the next invoice and send a revised statement. That is often faster than a refund and avoids a payment cycle in both directions. If the supplier cannot locate the receipt, ask them to trace it against their bank records and confirm in writing.

Where the supplier disputes the claim, escalate to your procurement or commercial contact rather than arguing with accounts receivable. The contract governs whether a deposit is refundable and on what timing, and those terms vary by jurisdiction and by agreement. If a refund is delayed, compare the financing effect with your own cost of funds before deciding whether to press for repayment or accept a credit against future orders.

Record the correction in the vendor record so the debit balance clears and the resolution is visible to the next reviewer. Match any credit memo to the original payment and the final invoice so the paper trail closes.

Stopping the next one

Require a purchase order or contract reference on every prepayment before it is paid, and record that reference on the vendor record at the same time. A deposit without a reference cannot be matched later. Put the deposit terms on the purchase order itself so the supplier and the AP team work from the same document.

Hold the final invoice until the open prepayment is resolved. A workable control is to block payment on any invoice where the vendor record shows an unapplied debit balance for the same purchase order, so the clerk either applies the deposit or documents why the invoice is paid gross. This does not require a new system; it requires the aging report to be reviewed before the payment run, not after.

Review vendor debit balances on a fixed schedule, not only at period end. Prepayments age quietly, and the longer one sits, the harder it is to match to an invoice already paid. Assign an owner for clearing stale balances and require a status note on every open prepayment.

On the supplier side, confirm at onboarding how deposits will appear on final invoices and which reference the supplier will use. Ask for a statement on a regular schedule. When a supplier changes billing systems or consolidates entities, recheck open prepayments, because references can be lost in the transition.

Questions

What does paying the full invoice after a deposit mean?

It means the deposit was paid up front and the supplier was then paid the full invoice amount again, because the deposit was not applied to the final invoice. The vendor record keeps the deposit as an open debit balance, and the supplier holds it as a credit.

How do I know if a deposit was applied to the final invoice?

Check the vendor record for an open debit balance tied to the same purchase order or contract. If the balance is still there after the final invoice is paid, the deposit has not been applied. A supplier statement showing the final invoice paid in full alongside the deposit also confirms it.

Can I net the deposit against the next invoice?

Often yes, if the supplier agrees and the contract allows it. Ask for a credit memo or written confirmation that the deposit will be applied to a specific invoice, then match the credit to that invoice. Get the revised statement so your records and theirs agree.

What if the supplier says the deposit was already credited?

Ask for the credit memo or statement line that shows the application, with the date and the invoice it reduced. If the supplier cannot produce it, escalate to your procurement contact and keep the debit balance open on your side until it is resolved.

Updated Nov 9, 2026. Figures on this page are calculated by ERPSav from the definitions shown. The explanatory text is drafted with AI from those figures and checked automatically before it is published. General information only, not legal, tax or financial advice.