Definition
A check cancelled in the ERP and with the bank so it cannot be cashed, recorded so that the bill it paid is open again.
Also called: void check, cancelled check
What it means
A Voided check has two sides, and AP teams get into trouble when they treat it as one. The accounting side cancels the check in your ERP and reopens the bill it paid. The bank side makes sure the check cannot be cashed. The entry alone does not do that. A check marked void in the ERP can still clear if the bank has no instruction to stop it.
Use a void when a check has the wrong payee or wrong amount, when it was damaged, or when it should not have gone out at all. The point is to put the bill back on the open list so it can be paid correctly or held. A voided check is not the same as a stop payment or a positive pay decision. Those are bank controls. It is also not the same as a stale-dated check, which is about age. Each has its own handling, and mixing them up leaves gaps.
Once the void is recorded, the bill is open again. If you reissue, tie the new check to the same bill and keep the old check record with the reason. If you do not reissue, watch the bill so it does not sit open and age while everyone assumes it was paid. The record should show what was voided, why, and what replaced it.
How it works in practice
The usual sequence is simple. AP finds the problem, voids the check in the ERP, asks the bank for a stop payment or uses positive pay to reject the item, confirms the bank has the instruction, and then reissues or holds the bill. If the paper check is in hand, mark it void and keep it with the file. Do not reissue until the bank side is confirmed.
Here is a small situation built from the core risk. A supplier bill is paid by check. The check goes to the wrong address. AP voids the check in the ERP and asks the bank for a stop payment. The bill reopens, and a new check is issued. If the original check arrives and is cashed as well, the supplier is paid twice. The ERP void did not prevent that. Only the bank action did, and only if it was in place before the original check was presented.
If the check already cleared, a void in the ERP does not pull the money back. That is an overpayment or a duplicate payment to recover, not a clean void. Contact the supplier, ask for a refund or credit, and do not simply reissue against the same bill without tracking the recovery. The supplier record and the payment history should show both the original payment and the recovery.
A void in a closed period is usually posted as a reversal dated in the current period. That keeps the closed period closed. Company policy and accounting rules can differ, so confirm the treatment your controller expects before you post.
Where it goes wrong
The first mistake is voiding in the ERP and assuming the bank knows. It does not. The check can still clear. The bill reopens, a new check goes out, and the old check pays too. That is the classic double payment from a void and reissue.
The second mistake is reissuing too early. AP voids the check, prints a new one, and sends it before the stop payment or positive pay rejection is confirmed. If the bank pays the original, the supplier has two checks for one bill. Confirm the bank side first, then reissue.
The third mistake is poor timing around the bank reconciliation. A voided check may be removed from the outstanding check list before the bank has confirmed the stop. Or it may stay on the list after it has been stopped, which makes the reconciliation harder to read. Match the void record to the bank instruction and to the reissued check.
Closed periods cause another error. Teams sometimes try to backdate the void or reopen the period to make it disappear. The safer route is the reversal dated in the current period, with the reason documented. A Voided check with no reason, no bank confirmation and no link to a replacement is a loose end that shows up later as a duplicate or an aged bill.
What to check
Before you void, check the bank status. Has the check presented? If yes, stop and treat it as a recovery. If no, request the stop payment or handle the positive pay exception. Get confirmation, not a verbal assurance. Bank rules for stop payments and positive pay vary by bank, account and contract, so use the timing your bank states.
After you void, check the bill. It should be open again. If you reissued, the new check should point to the same bill and the old check should be marked as replaced. The supplier record should not show two open payments for one bill. Look at the payment history, not only the current balance.
Check the reconciliation. Compare voided checks with stop payment requests and positive pay exceptions. Look for a reissued check and an original check that both cleared. That pattern is easy to miss when the amounts match and the supplier cashes both. Run a duplicate payment review on the supplier and the bill.
Check the period. If the void falls in a closed period, confirm the reversal is dated in the current period and approved under your policy. Keep the reason and bank confirmation with the file. That file is what lets the next person understand why the check was voided and whether the supplier was paid once or twice.
Questions
What is a Voided check in accounts payable?
A Voided check is a check cancelled in the ERP and with the bank so it cannot be cashed. The bill it paid is recorded as open again. The accounting entry and the bank instruction both matter.
Does voiding a check in the ERP stop the bank from paying it?
No. Voiding in the ERP changes your records and reopens the bill. A stop payment or positive pay instruction is what stops the bank from paying the check. Confirm the bank side before you reissue.
How is a voided check recorded in a closed period?
A void in a closed period is usually posted as a reversal dated in the current period. Company policy and accounting rules can differ. Confirm the treatment with your controller before posting.
Updated Nov 15, 2026. Figures on this page are calculated by ERPSav from the definitions shown. The explanatory text is drafted with AI from those figures and checked automatically before it is published. General information only, not legal, tax or financial advice.